Whirlpool Stove, Range, and Oven errorcodes list. Error codes appear on your Whirlpool oven’s display to let you know there is a problem. This complete list of Whirlpool oven faultcode definitions will assist you in finding the issue. Use the codes below to clear, check, troubleshoot, and repair your oven. Once you understand the error code displayed, you will know which part ofthe oven is faulty and causing the error. You can then purchase the part and fix the oven yourself. There are 3 letter error codes, 2 digit error codes, and 4 digit error codes on Whirlpool ovens. This means your Whirlpool oven will show either only 2 digits or two sets of 2 digits with a letter and a number. Example of 4 digit error code = e2 f3.
Whirlpool Range, Stove, Oven 3 Letter Error Codes:
Whirlpool Oven Error Code LOC
Reason/Condition for Error Code = Child LOCK is ON
Check/Troubleshoot = Press and hold the ‘Start’ or ‘Cancel’ button for ten seconds to remove LOC from display.
Whirlpool Oven Error Code PSH
Reason/Condition for Error Code = If Start is not pressed within 5 seconds, “PUSH” or “PSH” appears on the display – Press Start
If start is not pressed within 1 minute after pressing the keypad then the function is canceled and time is displayed.
Check/Troubleshoot = Reset power to the oven if you get a constant PSH error:
-Turn OFF circuit breaker to oven for one minute.
-Turn ON circuit breaker to oven.
-Check the oven for one minute to be sure the error code is cleared.
Whirlpool Range, Stove, Oven 2 Digit Error Codes:
Whirlpool Oven Error Code F0
No previous fault codes – press CANCEL to clear
Whirlpool Oven Error Code F1
Reason/Condition for Error Code = Defective Electronic Oven Control or EOC
Check/Troubleshoot = Unplug the oven power cord or turn OFF the circuit breaker – If F1 error persists then replace EOC
Replace/Check Parts = Electronic Oven Control (EOC)
Whirlpool Oven Error Code F2
Reason/Condition for Error Code = Oven Temperature Too High
Check/Troubleshoot = Check for welded contacts on both the bake and broil relays
Replace/Check Parts = Contact Relay – Control Board
Whirlpool Oven Error Code F3
Reason/Condition for Error Code = Open Oven Temperature Sensor
Replace/Check Parts = Replace Oven Temperature Sensor
Whirlpool Oven Error Code F4
Reason/Condition for Error Code = Oven Temperature Sensor Shorted
Replace/Check Parts = Replace Oven Temperature Sensor
Whirlpool Oven Error Code F5
Reason/Condition for Error Code = Control Board Fail
Replace/Check Parts = Replace Control Board
Whirlpool Oven Error Code F7
Reason/Condition for Error Code = Function Key Is Stuck
Replace/Check Parts = Replace Control Board
Whirlpool Oven Error Code F8
Reason/Condition for Error Code = Control Board Fail
Replace/Check Parts = Replace Control Board
Whirlpool Oven Error Code F9
Reason/Condition for Error Code = Oven Door Locking Fail
Check/Troubleshoot = Check door lock switches, stuck lock switch, wiring
Replace/Check Parts = Door Lock Switch
Whirlpool Oven Range Stove Parts
Whirlpool Range, Stove, Oven 4 Digit Error Codes:
Whirlpool Oven Error Code F2 E0 (E0 F2)
Reason/Condition for Error Code = Keypad Wiring Harness NOT Connected
Check/Troubleshoot = Unplug the oven power cord or turn OFF the circuit breaker. Reconnect keypad wiring harness. Plug the oven power cord back in or turn ON circuit breaker. Press CANCEL on the display. If fault code comes back after 1 minute then replace the keypad. If F2 E0 persists then replace the electronic oven control.
Replace/Check Parts = Keypad – Electronic Oven Control
Whirlpool Oven Error Code F2 E5 (E5 F2)
Reason/Condition for Error Code = CANCEL Key (Button) Is Faulty
Check/Troubleshoot = Unplug the oven power cord or turn OFF the circuit breaker. Reconnect keypad wiring harness. Plug the oven power cord back in or turn ON circuit breaker. Press CANCEL on the display. If fault code comes back after 1 minute then replace the keypad. If F2 E5 persists then replace the electronic oven control.
Replace/Check Parts = Keypad – Electronic Oven Control
Whirlpool Oven Error Code F2 E6 (E6 F2)
Reason/Condition for Error Code = CANCEL Key (Button) Is Faulty
Check/Troubleshoot = Unplug the oven power cord or turn OFF the circuit breaker. Reconnect keypad wiring harness. Plug the oven power cord back in or turn ON circuit breaker. Press CANCEL on the display. If fault code comes back after 1 minute then replace the keypad. If F2 E6 persists then replace the electronic oven control.
Replace/Check Parts = Keypad – Electronic Oven Control
Whirlpool Oven Error Code F3 E0 (E0 F3)
Reason/Condition for Error Code = Open Oven Temp Sensor Circuit OR Oven Temp Sensor Faulty
Check/Troubleshoot = Unplug the oven power cord or turn OFF the circuit breaker. Reconnect the oven temperature sensor wiring harness. Replace the wire harness if shorted. Use an ohm meter and check the oven temp sensor resistance. If resistance is not 1080 ohms at room temp then replace the oven temperature sensor. If oven temp sensor resistance checks good then replace the electronic oven control.
Replace/Check Parts = Oven Temperature Sensor – Wiring Harness – Electronic Oven Control
Whirlpool Oven Error Code F3 E1 (E1 F3)
Reason/Condition for Error Code = Oven Temp Sensor Faulty OR Shorted Oven Temp Circuit
Check/Troubleshoot = Unplug the oven power cord or turn OFF the circuit breaker. Reconnect the oven temperature sensor wiring harness. Replace the wire harness if shorted. Use an ohm meter and check the oven temp sensor resistance. If resistance is not 1080 ohms at room temp then replace the oven temperature sensor. If oven temp sensor resistance checks good then replace the electronic oven control.
Replace/Check Parts = Oven Temperature Sensor – Wiring Harness – Electronic Oven Control
Whirlpool Oven Error Code F3 E2 (E2 F3)
Reason/Condition for Error Code = Oven Temp Over 575 Degrees In BAKE Mode
Check/Troubleshoot = Unplug the oven power cord or turn OFF the circuit breaker. Reconnect the oven temperature sensor wiring harness. Replace the wire harness if shorted. Use an ohm meter and check the oven temp sensor resistance. If resistance is not 1080 ohms at room temp then replace the oven temperature sensor. If oven temp sensor resistance checks good then replace the electronic oven control.
Replace/Check Parts = Oven Temperature Sensor – Wiring Harness – Electronic Oven Control
Whirlpool Oven Error Code F3 E3 (E3 F3)
Reason/Condition for Error Code = Oven Temp TOO HIGH In CLEAN Mode
Check/Troubleshoot = Unplug the oven power cord or turn OFF the circuit breaker. Reconnect the oven temperature sensor wire. Replace the wire harness if shorted. Measure the oven temp sensor resistance using a volt/ohm meter. If resistance is not 1080 ohms at room temp then replace the oven temperature sensor. If the oven temperature sensor resistance and wire harness connections a check good then replace the electronic oven control.
Replace/Check Parts = Oven Temperature Sensor – Wire Harness – Electronic Oven Control
Whirlpool Oven Error Code F4 E1 (E1 F4)
Reason/Condition for Error Code = Meat Probe Faulty/Shorted
Check/Troubleshoot = Unplug the oven power cord or turn OFF the circuit breaker. Use a volt/ohm meter and measure the resistance of the meat probe. If resistance is not 59000 ohms at room temp then replace the meat probe. If resistance of meat probe checks good then insert the meat probe and check for a secure connection with probe and jack. If jack is worn then replace. Check that the wire harness on the meat probe jack is not loose. Replace the wire harness if needed.
Replace/Check Parts = Meat Probe – Meat Probe Jack – Wire Harness
Whirlpool Oven Error Code F5 E0 (E0 F5)
Reason/Condition for Error Code = Door Open BUT Latch Is Locked – Latch Switch Communicates A Locked Door
Check/Troubleshoot = Test the oven door switch by opening and closing the door. See if the oven light turns on and off. If the oven door switch is faulty then replace it. Unplug the oven power cord or turn OFF the circuit breaker. Connect any loose wire harnesses on the oven door lock assembly. Replace the wire harness if needed. Check the door lock assembly for faults and replace it if faulty.
Replace/Check Parts = Oven Door Switch – Oven Door Locking Assembly – Wire Harness
Whirlpool Oven Error Code F5 E1 (E1 F5)
Reason/Condition for Error Code = Self Clean Latch Will Not Lock or Unlock
Check/Troubleshoot = Unplug the oven power cord or turn OFF the circuit breaker. Reconnect loose wires on the oven door lock assembly wire harness. Replace wire harness if needed. Check the door lock assembly for faults and replace it if faulty.
Replace/Check Parts = Oven Door Locking Assembly – Wire Harness
Whirlpool Oven Error F5 E1
Whirlpool Oven Error E1 F2
Parts below are for Whirlpool Oven – Range – Stove
In association with replacement parts due to error codes.
Whirlpool Electronic Control for Range Oven
Whirlpool Oven Electronic Control
Whirlpool Oven Control Panel Assembly
Whirlpool Oven Sensor for Range
Whirlpool Terminal Block for Range Oven
Whirlpool Infinite Switch for Range Oven
Whirlpool Sensor for Range Oven
Need help repairing or troubleshooting an error code on your Whirlpool Oven, Range, or Stove? Leave your question below and we will be happy to assist you in fixing the problem.